MemeMaker

The Arduino Uno Rev3 is the newest version of our most popular product, the Arduino Uno - a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button.

Learn More

The Arduino Leonardo is a microcontroller board based on the ATmega32u4 (datasheet). It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.

Learn More

The Arduino Leonardo is a microcontroller board based on the ATmega32u4 (datasheet). It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.

Learn More

The Arduino Motor Shield is based on the L298 (datasheet), which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive two DC motors with your Arduino board, controlling the speed and direction of each one independently. You can also measure the motor current absorption of each motor, among other features. The shield is TinkerKit compatible, which means you can quickly create projects by pluggingTinkerKit modules to the board.

Learn More

The Arduino Ethernet Shield connects your Arduino to the internet in mere minutes. Just plug this module onto your Arduino board, connect it to your network with an RJ45 cable (not included) and follow a few simple instructions to start controlling your world through the internet. 

Learn More

Open Softwear is a book about fashion and technology. More precisely it is a book about Arduino boards, conductive fabric, resistive thread, soft buttons, LEDs, and some other things. We started researching five years ago thanks to the support of K3,  School of Arts and Communication, Malmö University, Sweden.

Learn More

The Arduino WiFi Shield connects your Arduino to the internet wirelessly. Connect it to your wireless network by following a few simple instructions to start controlling your world through the internet. As always with Arduino, every element of the platform – hardware, software and documentation – is freely available and open-source. This means you can learn exactly how it's made and use its design as the starting point for your own circuits.

Learn More

Nabduino - no firewall hassle! Nabduino is a hardware prototyping board created by Nabto for prototyping the Nabto communication platform. If you want to easily remote monitor or develop a nice web-interface on your embedded device, the Nabduino is something for you. Learn More

The Arduino Mega 2560 is a microcontroller board based on the ATmega2560 (datasheet). It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button.

Learn More

Plaast is a versatile plastic material, ideal for crafting, repairing and prototyping. It is very easy to use, even of you have no experience beforehand.

The material can be molten in hot water where it, and once it becomes completely transparent, can be brought into any shape. When cooled off completely, it is extremely sturdy and can be machined easily.

For inspiration on use cases, see the links below or on the product page.

Learn More

The Arduino Mega ADK is a microcontroller board based on the ATmega2560 (datasheet). It has a USB host interface to connect with Android based phones.

Learn More

New from the fine people who have brought us the Beagle Board, we now have a smaller, lighter, but powerful single board linux computer, Beagle Bone! We like this move to a more compact and integrated SBC. For example, there is onboard Ethernet and USB host, as well as a USB client interface (a FTDI chip for shell access). It even comes preloaded with Angstrom Linux on the 4 GB microSD card! 

Package includes:

• Fully assembled and tested BeagleBone A4
• Mini-B USB cable
• 4 GB microSD card with preloaded Angstrom Linux
• MicroSD to SD card adapter

Learn More

Add some circuitry to your Beagle Bone with the lovely Proto Cape. If you have a 'Bone you need one of these! This PCB fits neatly on top of a Beagle Bone, without getting in the way of the Ethernet jack, and provides a breakout to both 46 pin headers - with individual numbering to keep them straight. We also threw down some strips to access the 5V and 3V power supplies as well as two SMT breakouts, one for SOIC-8's and one for SOT-23's. Learn More

This is a thorough introduction, updated for Arduino 1.0. It gives you lots of ideas for projects and helps you work with them right away. From getting organized to putting the final touches on your prototype, all the information you need is here! Inside, you’ll learn about:     - The Arduino hardware and software development environment     - Basics of electricity and electronics     - Prototyping on a solderless breadboard     - Drawing a schematic diagram

 

Learn More

We now have the plates from the ARDX available separately. Acrylic plate is engraved and cut here at the Adafruit factory. There are mounting holes for your Arduino and a space that fits a half sized breadboard very nicely.

THIS DOES NOT FIT THE ARDUINO MEGA.

Learn More

This is a 9V battery pack with on/off switch and a pre-attached 5.5mm/2.1mm barrel plug. Use this to battery-power your Arduino (or other electronic projects) - it's ready to go out of the box! Battery not included. Learn More

The Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino Nano 3.0) or ATmega168 (Arduino Nano 2.x). It has more or less the same functionality of the Arduino Duemilanove, but in a different package. It lacks only a DC power jack, and works with a Mini-B USB cable instead of a standard one. The Nano was designed and is being produced by Gravitech.

Learn More

Kit with parts to participate in an Arduino Workshop. Learn More

The Arduino Mega 2560 is a microcontroller board based on the ATmega2560 (datasheet). It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega is compatible with most shields designed for the Arduino Duemilanove or Diecimila.

The Mega 2560 is an update to the Arduino Mega 1280, which it replaces.

Learn More

The Arduino Mega is a microcontroller board based on the ATmega1280 (datasheet). It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega is compatible with most shields designed for the Arduino Duemilanove or Diecimila.

Learn More

Standard HD44780 LCDs are useful for creating standalone projects.

Learn More

These displays are small, only about 1" diagonal, but very readable due to the high contrast of an OLED display. This display is made of 128x32 individual white OLED pixels, each one is turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why the display has such high contrast; we really like this miniature display for its crispness! 

Learn More

The little dev board keeps it simple, with just the bare essentials:

• Atmega32u4 - AVR core with USB capability. 32K flash, 2.5K RAM running at 16MHz
• Standard AVR 6-pin ISP connector for direct programming (when you need the extra space)
• Big Bootload/Reset button
• 500mA fuse on the USB power line
• Power LED and 'user' LED (also indicates when the bootloader is active)
• Fits nicely in any breadboard
• 4 mounting holes

Learn More

75 flexible stranded core wires with stiff ends molded on in red, orange, yellow, green, blue, brown, black and white. These are a major improvement over the "box of bent wires" that are sometimes sold with breadboards, and faster than stripping your own solid core wires. Makes breadboarding super fast. Learn More

This proto-board is the PCB you always wish you had, but never realized it! We took the basic layout of a half-sized breadboard and turned that into a beautiful PCB. The top side has a white silkscreen, and the same markings you're familiar with, to make transferring components easy. Learn More

PIR sensors are used to detect motion from pets/humanoids from about 20 feet away (possibly works on zombies, not guaranteed). This one has an adjustable delay before firing (approx 0.3-18 seconds), adjustable sensitivity and we include a 1 foot (30 cm) cable with a socket so you can easily reposition the sensor or mount it using the two drills on either side Learn More

This sensor is essentially a reed switch, encased in an ABS plastic shell. Normally the reed is 'open' (no connection between the two wires). The other half is a magnet. Learn More

Base kit to extend your Arduino with your own wired circuit.

The kit is delivered unassembled, so break out your soldering irons!

Learn More

Use these to stack shields on your Arduino! These are standard 6-pin and 8-pin 0.1" spacing female headers...with a twist! The pins are extra long which means you can use these to stack shields! The legs are 10.5mm (0.42") long, so after the PCB thickness (1.7mm/0.07") you have a height of 8.8mm (0.35"). Comes in a package of 2 8-pin headers and 2 6-pin headers. 

Learn More

This is only the printed circuit board for Adafruits adjustable breadboard power supply project Learn More

These stickers are a must for anyone making a project with an ATmegaXX8 chip such as the ATmega48, ATmega8, ATmega88, ATmega168, or ATmega328. Learn More